Husaberg
Go Back   Husaberg Forum > Husaberg Forum > Husaberg

Husaberg Husaberg Forum - Husaberg Motorcycle Forum


Reply
 
LinkBack Thread Tools Display Modes
September 12th, 2011, 04:05 PM   #1
Junior Member
 
Joined: Nov 2010
From: Utah

Posts: 4
Thanks: 0

I Ride:
Flash code number 06 on a 2010 570 fe

I have the a 2010 570 FE, I just replaced the fuel pump, filter because of stalling and later would not start.
Now that I have it all back together, I am getting a flash code number 6 ( six short flashes) I have check the position of the throttle sensor, the screw it tight that holds it in place, everything seems normal connection is good.

Disconnected the batteries and adjusted the sensor position, reconnect and the same #6 flash code comes up.

I have tried everything I can think of, any suggestions???

Please help!!!!
Pitster is offline  
 
September 12th, 2011, 08:52 PM   #2
Senior Member
 
Joined: Oct 2009
From: Galston Australia

Posts: 995
Thanks: 12

I Ride:
Re: Flash code number 06 on a 2010 570 fe

Fuel Injection warning lamp flashes:
6x short = Throttle position sensor (TPS)

Did you maybe damage a wire in the main loom taking the Tank on and off?
The Wiring Loom seems to be vulnerable where it runs past the top of the Rear Shock Absorber.

I have seen 1 other post saying they had replaced a TPS Sensor:
70 degree durability and issue thread.

There are 3 Wires on the TPS:



You can easily test pin 2 (Blue) and pin 3 (Black) in the wiring loom.
Disconnect the TPS connector.
Just have a Multimeter on low voltage DC Scale (say 20V DC).
Put the Multimeter Red Lead on the Blue Wire in the TPS connector and the Multimeter Black Lead on the Black Wire in the TPS connector and you should see +5V (4.9V to 5.1V to be exact). You will have to touch the starter to get the power relay to click in, to get this measurement.


To test the 3rd (Pin 1 yellow) Wire you would have to disconnect the EFI Computer under the seat and measure the resistance of the wire by putting one lead of the Multimeter on the Pin 3 in the TPS connector and the equivalent wire in the EFI Connector under the seat which is the yellow wire Pin 5. Switch the Multimeter to the Resistance Scale and look for a very low resistance, something close to zero ohms. Something like 0.6 Ohms.
You should also check that wire is not shorted to Chassis Ground by measuring the Resistance between the yellow wire and the Bike Frame (Ground). It should be infinity (Off the scale on the resistance setting).

You can test the TPS Sensor by measuring the Resistance between pins 2 and 3 on the TPS Sensor. Disconnect the TPS connector and place the Multimeter on the Resistance scale and measure this resistance. Post up what resistance it is and I will measure the resistance on mine to compare.
Next, Measure the resistance between Pin 1 and Pin 3 of the TPS sensor. That resistance should change as you slowly open the throttle. Post up what you see. It will either go from a high to low reading or a low to high reading as you open the throttle.
The TPS Sensor is just a simple variable resistor, I just donít know the resistance values.
Davo is offline  
Reply

  Husaberg Forum > Husaberg Forum > Husaberg

Tags
2010, 570, code, flash, number



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
2010 FE390 service manual part number? Garrison Mechanical 6 October 24th, 2012 07:51 PM
Flash boil in tank erniebearskin Fuel 43 August 15th, 2012 04:06 AM
Right blinker causes double flash mrt10x Electrical 1 June 18th, 2012 12:44 PM
Flash Code 06 Husaberg 570 2009 Fault kiwiglenn Electrical 1 March 13th, 2010 02:19 PM
isle of man news flash....... cypher Ride Reports 16 December 19th, 2007 04:27 PM


Facebook Twitter Google+ RSS Feed