Husaberg
Go Back   Husaberg Forum > Mechanical and Technical > Electrical

Electrical Electrical Forum - wiring and more


Reply
 
LinkBack Thread Tools Display Modes
September 4th, 2020, 06:54 PM   #1
Junior Member
 
Joined: Sep 2020
From: Australia

Posts: 1
Thanks: 0

I Ride:
2011 fe 450 no spark /fuel pump

I have a 2011 fe 450 was running son washed it no no spark no
Power to fuel pump
Just bought the bike second hand wiring looks to be std mo monster stuff
Cheers
Glenny is offline  
 
September 4th, 2020, 09:18 PM   #2
Senior Member
 
Rainerio's Avatar
 
Joined: Jun 2013
From: San Francisco CA. USA

Posts: 1,050
Thanks: 255

I Ride: 8 Berg’s 2005-2011 2 Husky’s 1986&7 2009 Buell & 2006 Ducati
Check fuses under the seat. If not push the starter for a second listen for fuel pump if it does make noise I’d say bad pump. Loose connections?

Last edited by Rainerio; September 4th, 2020 at 09:21 PM.
Rainerio is offline  
September 6th, 2020, 07:07 PM   #3
TnT
Junior Member
 
Joined: Jul 2020
From: Spokane

Posts: 6
Thanks: 0

I Ride:
Check power to fuses first. If fuses all have power while cranking (both sides of the fuses) then check for water in the computer harness where it plugs in.
TnT is offline  
September 9th, 2020, 04:45 PM   #4
Member
 
Joined: Mar 2013
From: NY

Posts: 84
Thanks: 7

I Ride: 2010 FX450 2011 KTM 250XC
Pull the spark plug cap off pull out the threaded lug with pliers clean off the carbon reassemble . Be carful a resistor will be pushed out from an internal spring do it in a location that you won’t lose the resistor . Test it should be 5k ohms these bikes were plagued with flameouts years later I found this is one of the reasons .
cambo is offline  
September 10th, 2020, 07:33 PM   #5
TnT
Junior Member
 
Joined: Jul 2020
From: Spokane

Posts: 6
Thanks: 0

I Ride:
Originally Posted by cambo View Post
Pull the spark plug cap off pull out the threaded lug with pliers clean off the carbon reassemble . Be carful a resistor will be pushed out from an internal spring do it in a location that you won’t lose the resistor . Test it should be 5k ohms these bikes were plagued with flameouts years later I found this is one of the reasons .
That wouldn't cause no power to the fuel pump
TnT is offline  
September 11th, 2020, 06:13 AM   #6
Member
 
Joined: May 2017
From: United States

Posts: 99
Thanks: 19

I Ride:
The most common area for the harness to be damaged on these is where it runs against the frame next to the rear damper/spring. If there is abrasive damage moisture could have entered during the wash. I would have a close look in that area along with confirming no water damaged the engine stop or start button on the handle bars.

Another area to check are the two hex screws and spade connectors on the primary engine power relay that sits on top of the battery.
NoClassic is offline  
Reply

  Husaberg Forum > Mechanical and Technical > Electrical

Tags
2011, 450, or fuel, pump, spark



Thread Tools
Display Modes


Similar Threads
Thread Thread Starter Forum Replies Last Post
It does not ignite gasoline pump and has no spark - FE 390 acarrero Electrical 10 July 13th, 2019 12:55 PM
No Spark No Fuel Pump noise. B3RG Husaberg 6 August 7th, 2017 02:40 AM
2011 Husaberg 570 Wont Start After Soldering Fuel Pump Wires In Wiring Harness titan Electrical 8 July 10th, 2015 04:04 AM
For Sale: 2011 FE450 Fuel Pump Assemblies (3) Bigninjazx12r Classifieds 7 January 13th, 2015 09:48 AM
run out of fuel.. How to prime fuel pump? lyon90 Fuel 2 August 12th, 2011 10:21 AM


Facebook Twitter Google+ RSS Feed